Home | Testing Services | Technical Information | Consulting | Customer Services | Careers | Contact Us
►TOYS
►REGULATIONS OF DIFFERENT COUNTRIES
EMC Directive – 2004/108/EC (repealing Directive
89/336/EEC) – EU Directive relating to electromagnetic compatibility (emission and immunity requirements on electrical/electronic products)
This
Directive provides for CE marking.
Requirements of the Directive
The
Electromagnetic Compatibility Directive (EMC) sets essential requirements for all electrical and electronic
equipment that may interfere with other equipment or that may be interfered
with by other equipment.
In essence the requirements of the Directive are very simple - it
basically states that products must not emit unwanted electromagnetic pollution
(interference). Because there is a certain amount of electromagnetic pollution
in the environment, the Directive also states that products must be immune to a
reasonable amount of interference. The Directive itself gives no figures or
guidelines on what the required level of emissions or immunity are, nor does it
state the frequency band limits. This interpretation of the Directive's
requirements is left to the standards that are used to demonstrate compliance
with the Directive.
Electromagnetic
Interference
In
general, the radiated emission level of the sample is measured.
The
maximum electromagnetic disturbance generated by the sample shall be such as
not to hinder the use of other electrical / electronic equipment.
Electromagnetic
Immunity
To
certain types of electrical products, Electro Static Discharge (ESD) tests are
conducted.
ESD
tests ensure that the sample is constructed in such a way that it has an
adequate level of electromagnetic immunity so as to allow its unhindered
operation taking into account the levels of disturbance generated by other electrical
/ electronic equipment.
Scope of the Directive
The
Electromagnetic Compatibility Directive (EMC) sets essential requirements for all
electrical and electronic equipment that may interfere with other equipment or
that may be interfered with by other equipment.
The EMC
Directive applies to:
All electrical
and electronic equipment, systems and installations containing electrical
and/or electronic components, that can cause electromagnetic interference or
whose function can be degraded by electromagnetic interference.
Principal protection requirements
The
maximum electromagnetic disturbance generated by the apparatus shall be such as
not to hinder the use of in particular the following apparatus (please note
this is an illustrative list):
a domestic radio and television receivers
b industrial manufacturing equipment
c mobile radio equipment
d mobile radio and commercial radiotelephone
equipment
e medical and scientific apparatus
f information technology equipment
g domestic appliances and household
electronic equipment
h aeronautical and marine radio apparatus
i educational electronic equipment
j telecommunications networks and apparatus
k radio and television broadcast
transmitters
l lights and fluorescent lamps.
Demonstrating compliance
The Directive allows three routes to compliance. Of these, the EC type
examination route, which requires full testing to recognized standards, is only
mandatory for telecommunications (i.e. transmitting) apparatus. For other equipment
there is the Manufacturer's Declaration of Conformity or the Technical
Construction File.
The Manufacturers Declaration of Conformity allows the manufacturer to
compare the performance of the equipment with the requirements of the relevant
standards, and if they are sure that the standards are met, the manufacturer
makes a declaration that the Directive has been complied with. Testing may be
required in order to demonstrate that the appliance does meet the requirements
of the standard, but this is not mandatory.
The Technical Construction File route to compliance is designed for
equipment for which there is no clearly applicable standard - or which is of
such a size that testing in a normal laboratory facility is not possible. The
manufacturer creates a file that provides a range of information, and draws it
together to form the conclusion that the product meets the requirements of the
EMC Directive. This conclusion is then audited by a Conformity Assessment Body,
which takes responsibility for ensuring that the logic used to justify the
declaration of compliance is valid and accurate and issues a certificate
accordingly.
Administrative requirements under the Directive
While the essence of the Directive is, of course, to ensure that
products meet the essential protection requirements of immunity and emissions,
there are two other requirements that the Directive makes of manufacturers or
importers. These are to assist officials charged with responsibility for
enforcing the Directive. One is that the product, its instructions or
packaging, be marked with the CE logo. The other is that the manufacturer or
importer must make an official pronouncement of the product's compliance with
the Directive, known as a Declaration of Conformity.
Summary
list of titles and references of harmonised standards relating to EMC
This list replaces all
the previous lists published in the Official Journal of the European Union. The
Commission ensures the updating of this list.
However, this list does not have any legal validity; only publication in the
Official Journal produces legal affect.
|
Reference and title of the standard |
Reference of the superseded standard |
Date of cessation of presumption of conformity of the superseded standard Note
1 |
|
EN
50065-1:2001 Signalling
on low-voltage electrical installations in the frequency range 3 kHz to 148,5
kHz - Part 1: General requirements, frequency bands and electromagnetic
disturbances |
|
|
|
EN
50065-2-1:2003 Signalling
on low-voltage electrical installations in the frequency range 3 kHz to 148,5
kHz - Part 2-1: Immunity requirements for mains communications equipment and
systems operating in the range of frequencies 95 kHz to 148,5 kHz and
intended for use in residential, commercial and light industrial environments
|
|
|
|
Amendment A1:2005 to EN 50065-2-1:2003 |
Note 3 |
01.07.2008
|
|
EN 50065-2-2:2003 Signalling on low-voltage electrical installations
in the frequency range 3 kHz to 148,5 kHz - Part 2-2: Immunity requirements
for mains communications equipment and systems operating in the range of
frequencies 95 kHz to 148,5 kHz and intended for use in industrial
environments |
|
|
|
Amendment A1:2005 to EN 50065-2-2:2003 |
Note 3 |
01.07.2008
|
|
EN 50065-2-3:2003 Signalling on low-voltage electrical installations
in the frequency range 3 kHz to 148,5 kHz - Part 2-3: Immunity requirements
for mains communications equipment and systems operating in the range of frequencies
3 kHz to 95 kHz and intended for use by electricity suppliers and
distributors |
|
|
|
Amendment A1:2005 to EN 50065-2-3:2003 |
Note 3 |
01.07.2008
|
|
EN 50083-2:2001 Cable networks for television signals, sound signals
and interactive services - Part 2: Electromagnetic compatibility for
equipment |
|
|
|
Amendment A1:2005 to EN 50083-2:2001 |
Note 3 |
01.04.2008
|
|
EN 50083-2:2006 Cable networks for television signals, sound signals
and interactive services - Part 2: Electromagnetic compatibility for
equipment |
|
|
|
EN
50090-2-2:1996 Home
and Building Electronic Systems (HBES) - Part 2-2: System overview - General
technical requirements |
|
|
|
EN
50091-2:1995 Uninterruptible
power systems (UPS) - Part 2: EMC requirements |
|
|
|
EN
50121-1:2006 Railway
applications - Electromagnetic compatibility - Part 1: General |
|
|
|
EN
50121-2:2006 Railway
applications - Electromagnetic compatibility - Part 2: Emission of the whole
railway system to the outside world |
|
|
|
EN
50121-3-1:2006 Railway
applications - Electromagnetic compatibility - Part 3-1: Rolling stock -
Train and complete vehicle |
|
|
|
EN
50121-3-2:2006 Railway
applications - Electromagnetic compatibility - Part 3-2: Rolling stock -
Apparatus |
|
|
|
EN
50121-4:2006 Railway
applications - Electromagnetic compatibility - Part 4: Emission and immunity
of the signalling and telecommunications apparatus |
|
|
|
EN
50121-5:2006 Railway
applications - Electromagnetic compatibility - Part 5: Emission and immunity
of fixed power supply installations and apparatus |
|
|
|
EN
50130-4:1995 Alarm
systems - Part 4: Electromagnetic compatibility - Product family standard:
Immunity requirements for components of fire, intruder and social alarm
systems |
|
|
|
Amendment A1:1998 to EN 50130-4:1995 |
Note 3 |
Date expired |
|
Amendment A2:2003 to EN 50130-4:1995 |
Note 3 |
01.09.2007
|
|
EN
50148:1995 Electronic taximeters |
|
|
|
EN 50240:2004 Electromagnetic
compatibility (EMC) - Product standard for resistance welding equipment |
|
|
|
EN
50263:1999 Electromagnetic
compatibility (EMC) - Product standard for measuring relays and protection
equipment |
|
|
|
EN
50270:1999 Electromagnetic
compatibility - Electrical apparatus for the detection and measurement of
combustible gases, toxic gases or oxygen |
|
|
|
EN
50293:2000 Electromagnetic
compatibility - Road traffic signal systems - Product standard |
|
|
|
EN
50295:1999 Low-voltage
switchgear and controlgear - Controller and device interface systems -
Actuator Sensor interface (AS-i) |
|
|
|
EN
50370-1:2005 Electromagnetic
compatibility (EMC) - Product family standard for machine tools - Part 1:
Emission |
|
|
|
EN
50370-2:2003 Electromagnetic
compatibility (EMC) - Product family standard for machine tools - Part 2:
Immunity |
|
|
|
EN
50412-2-1:2005 Power
line communication apparatus and systems used in low-voltage installations in
the frequency range 1,6 MHz to 30 MHz - Part 2-1: Residential, commercial and
industrial environment - Immunity requirements |
|
|
|
EN
50428:2005 Switches
for household and similar fixed electrical installations - Collateral
standard - Switches and related accessories for use in home and building
electronic systems (HBES) |
|
|
|
EN
50470-1:2006 Electricity
metering equipment (a.c.) - Part 1: General requirements, tests and test
conditions - Metering equipment (class indexes A, B and C) |
|
|
|
EN
55011:1998 Industrial,
scientific and medical (ISM) radio-frequency equipment - Radio disturbance
characteristics - Limits and methods of measurement (CISPR
11:1997 (Modified)) |
|
|
|
Amendment A1:1999 to EN 55011:1998 (CISPR
11:1997/A1:1999) |
Note 3 |
Date expired |
|
Amendment A2:2002 to EN 55011:1998 (CISPR
11:1999/A2:2002) |
Note 3 |
Date expired |
|
EN
55011:2007 Industrial,
scientific and medical (ISM) radio-frequency equipment - Electromagnetic
disturbance characteristics - Limits and methods of measurement (CISPR
11:2003 (Modified) |
|
|
|
Amendment A2:2007 to EN 55011:2007 (CISPR
11:2003/A2:2006) |
Note 3 |
01.11.2009 |
|
EN
55012:2002 Vehicles,
boats and internal combustion engine driven devices - Radio disturbance
characteristics - Limits and methods of measurement for the protection of
receivers except those installed in the vehicle/boat/device itself or in
adjacent vehicles/boats/devices (CISPR
12:2001) |
|
|
|
Amendment A1:2005 to EN 55012:2002 (CISPR
12:2001/A1:2005) |
Note 3 |
01.03.2008 |
|
EN
55013:2001 Sound
and television broadcast receivers and associated equipment - Radio
disturbance characteristics - Limits and methods of measurement (CISPR
13:2001 (Modified)) |
|
|
|
Amendment A1:2003 to EN 55013:2001 (CISPR
13:2001/A1:2003) |
Note 3 |
Date expired |
|
Amendment A2:2006 to EN 55013:2001 (CISPR
13:2001/A2:2006) |
Note 3 |
01.03.2009 |
|
EN
55014-1:2000 Electromagnetic
compatibility - Requirements for household appliances, electric tools and
similar apparatus - Part 1: Emission (CISPR
14-1:2000) |
|
|
|
Amendment A1:2001 to EN 55014-1:2000 (CISPR
14-1:2000/A1:2001) |
Note 3 |
Date expired |
|
Amendment A2:2002 to EN 55014-1:2000 (CISPR
14-1:2000/A2:2002) |
Note 3 |
Date expired |
|
EN
55014-1:2006 Electromagnetic
compatibility - Requirements for household appliances, electric tools and
similar apparatus - Part 1: Emission (CISPR
14-1:2005) |
|
|
|
EN
55014-2:1997 Electromagnetic
compatibility - Requirements for household appliances, electric tools and
similar apparatus - Part 2: Immunity - Product family standard (CISPR 14-2:1997) |
|
|
|
Amendment A1:2001 to EN 55014-2:1997 (CISPR
14-2:1997/A1:2001) |
Note 3 |
Date expired |
|
EN
55015:2000 Limits
and methods of measurement of radio disturbance characteristics of electrical
lighting and similar equipment (CISPR
15:2000) |
|
|
|
Amendment A1:2001 to EN 55015:2000 (CISPR
15:2000/A1:2001) |
Note 3 |
Date expired |
|
Amendment A2:2002 to EN 55015:2000 (CISPR
15:2000/A2:2002) |
Note 3 |
Date expired |
|
EN 55015:2006 Limits
and methods of measurement of radio disturbance characteristics of electrical
lighting and similar equipment (CISPR
15:2005) |
|
|
|
EN 55020:2002 Sound
and television broadcast receivers and associated equipment - Immunity
characteristics - Limits and methods of measurement (CISPR
20:2002) |
|
|
|
Amendment A1:2003 to EN 55020:2002 (CISPR
20:2002/A1:2002) |
Note 3 |
Date expired |
|
Amendment A2:2005 to EN 55020:2002 (CISPR
20:2002/A2:2004) |
Note 3 |
01.02.2008 |
|
EN 55020:2007 Sound
and television broadcast receivers and associated equipment - Immunity
characteristics - Limits and methods of measurement (CISPR
20:2006) |
|
|
|
EN 55022:1998 Information
technology equipment - Radio disturbance characteristics - Limits and methods
of measurement (CISPR
22:1997 (Modified)) |
|
|
|
Amendment A1:2000 to EN 55022:1998 (CISPR
22:1997/A1:2000) |
Note 3 |
01.10.2009 |
|
Amendment A2:2003 to EN 55022:1998 (CISPR
22:1997/A2:2002) |
Note 3 |
01.10.2009 |
|
EN 55022:2006 Information
technology equipment - Radio disturbance characteristics - Limits and methods
of measurement (CISPR
22:2005 (Modified)) |
|
|
|
EN 55024:1998 Information
technology equipment - Immunity characteristics - Limits and methods of
measurement (CISPR
24:1997 (Modified)) |
|
|
|
Amendment A1:2001 to EN 55024:1998 (CISPR
24:1997/A1:2001) |
Note 3 |
Date expired |
|
Amendment A2:2003 to EN 55024:1998 (CISPR
24:1997/A2:2002) |
Note 3 |
Date expired |
|
EN 55103-1:1996 Electromagnetic
compatibility - Product family standard for audio, video, audio-visual and
entertainment lighting control apparatus for professional use - Part 1:
Emission |
|
|
|
EN 55103-2:1996 Electromagnetic
compatibility - Product family standard for audio, video, audio-visual and
entertainment lighting control apparatus for professional use - Part 2:
Immunity |
|
|
|
EN 60204-31:1998 Safety
of machinery - Electrical equipment of machines - Part 31: Particular safety
and EMC requirements for sewing machines, units and systems (IEC
60204-31:1996 (Modified)) |
|
|
|
EN 60439-1:1999 Low-voltage
switchgear and controlgear assemblies - Part 1: Type-tested and partially
type-tested assemblies (IEC
60439-1:1999) |
|
|
|
EN 60669-2-1:2000
Switches
for household and similar fixed electrical installations - Part 2-1:
Particular requirements - Electronic switches (IEC
60669-2-1:1996 (Modified) |
|
|
|
Amendment A2:2001 to EN 60669-2-1:2000 (IEC
60669-2-1:1996/A2:1999 (Modified)) |
Note 3 |
Date expired |
|
EN 60669-2-1:2004 Switches
for household and similar fixed electrical installations - Part 2-1:
Particular requirements - Electronic switches (IEC
60669-2-1:2002 (Modified)) |
|
|
|
EN 60669-2-2:1997 Switches
for household and similar fixed electrical installations - Part 2: Particular
requirements - Section 2: Electromagnetic remote-control switches (RCS) (IEC
60669-2-2:1996) |
|
|
|
EN 60669-2-3:1997 Switches
for household and similar fixed electrical installations - Part 2-3:
Particular requirements - Time-delay switches (TDS) (IEC 60669-2-3:1997) |
|
|
|
EN 60730-1:1995 Automatic
electrical controls for household and similar use - Part 1: General
requirements (IEC
60730-1:1993 (Modified)) |
|
|
|
Amendment A11:1996 to EN 60730-1:1995
|
Relevant generic standard(s) |
Date expired |
|
Amendment A17:2000 to EN 60730-1:1995
|
Note 3 |
Date expired |
|
EN 60730-1:2000 Automatic
electrical controls for household and similar use - Part 1: General
requirements (IEC
60730-1:1999 (Modified)) |
|
|
|
Amendment A1:2004 to EN 60730-1:2000 (IEC
60730-1:1999/A1:2003 (Modified)) |
Note 3 |
- |
|
EN 60730-2-5:1995 Automatic electrical controls for household and
similar use - Part 2: Particular requirements for automatic electrical burner
control systems (IEC 60730-2-5:1993 (Modified)) |
|
|
|
EN 60730-2-5:2002 Automatic
electrical controls for household and similar use - Part 2-5: Particular
requirements for automatic electrical burner control systems (IEC
60730-2-5:2000 (Modified)) |
|
|
|
Amendment A1:2004 to EN 60730-2-5:2002 (IEC
60730-2-5:2000/A1:2004 (Modified)) |
EN 60730-2-5:1995 |
01.12.2008 |
|
Amendment A11:2005 to EN 60730-2-5:2002
|
Note 3 |
01.12.2008
|
|
EN 60730-2-6:1995 Automatic electrical controls for household and
similar use - Part 2: Particular requirements for automatic electrical
pressure sensing controls including mechanical requirements (IEC 60730-2-6:1991 (Modified)) |
|
|
|
Amendment A1:1997 to EN 60730-2-6:1995 (IEC
60730-2-6:1991/A1:1994 (Modified)) |
EN 60730-1:1995 |
Date expired |
|
EN 60730-2-7:1991 Automatic
electrical controls for household and similar use - Part 2: Particular
requirements for timers and time switches (IEC
60730-2-7:1990 (Modified)) |
|
|
|
Amendment
A1:1997 to EN 60730-2-7:1991 (IEC 60730-2-7:1990/A1:1994 (Modified)) |
EN 60730-1:1995 |
Date expired |
|
EN
60730-2-8:1995 Automatic
electrical controls for household and similar use - Part 2: Particular
requirements for electrically operated water valves, including mechanical
requirements (IEC
60730-2-8:1992 (Modified)) |
|
|
|
Amendment A1:1997 to EN 60730-2-8:1995 (IEC
60730-2-8:1992/A1:1994 (Modified)) |
EN 60730-1:1995 |
Date expired |
|
>
Amendment A2:1997 to EN 60730-2-8:1995 (IEC
60730-2-8:1992/A2:1997) |
Note 3 |
Date expired |
|
EN
60730-2-8:2002 Automatic
electrical controls for household and similar use - Part 2-8: Particular
requirements for electrically operated water valves, including mechanical requirements
(IEC
60730-2-8:2000 (Modified)) |
|
|
|
Amendment A1:2003 to EN 60730-2-8:2002 (IEC
60730-2-8:2000/A1:2002 (Modified)) |
Note 3 |
01.12.2008
|
|
EN
60730-2-9:1995 Automatic electrical controls for household and
similar use - Part 2: Particular requirements for temperature sensing
controls (IEC 60730-2-9:1992 (Modified)) |
|
|
|
Amendment A1:1996 to EN 60730-2-9:1995 (IEC
60730-2-9:1992/A1:1994 (Modified)) |
EN 60730-1:1995 |
Date expired |
|
Amendment A2:1997 to EN 60730-2-9:1995 (IEC
60730-2-9:1992/A2:1994 (Modified)) |
Note 3 |
Date expired |
|
EN 60730-2-9:2002 Automatic
electrical controls for household and similar use - Part 2-9: Particular
requirements for temperature sensing controls (IEC
60730-2-9:2000 (Modified)) |
|
|
|
Amendment A2:2005 to EN 60730-2-9:2002 (IEC
60730-2-9:2000/A2:2004 (Modified)) |
Note 3 |
01.12.2007 |
|
Amendment A1:2003 to EN 60730-2-9:2002 (IEC
60730-2-9:2000/A1:2002 (Modified)) |
Note 3 |
01.12.2008
|
|
EN
60730-2-11:1993 Automatic electrical controls for household and
similar use - Part 2-11: Particular requirements for energy regulators (IEC 60730-2-11:1993) |
|
|
|
Amendment A1:1997 to EN 60730-2-11:1993 (IEC
60730-2-11:1993/A1:1994 (Modified)) |
EN 60730-1:1995 |
Date expired |
|
Amendment A11:2005 to EN 60730-2-11:1993 |
Note 3 |
01.03.2009
|
|
EN
60730-2-13:1998 Automatic electrical controls for household and
similar use - Part 2-13: Particular requirements for humidity sensing
controls (IEC 60730-2-13:1995 (Modified)) |
|
|
|
Amendment A11:2005 to EN 60730-2-13:1998 |
Note 3 |
01.02.2009
|
|
EN
60730-2-14:1997 Automatic electrical controls for household and
similar use - Part 2-14: Particular requirements for electric actuators (IEC 60730-2-14:1995 (Modified)) |
|
|
|
Amendment A1:2001 to EN 60730-2-14:1997 (IEC
60730-2-14:1995/A1:2001) |
Note 3 |
01.07.2008 |
|
EN
60730-2-18:1999 Automatic
electrical controls for household and similar use - Part 2-18: Particular
requirements for automatic electrical water and air flow sensing controls,
including mechanical requirements (IEC
60730-2-18:1997 (Modified)) |
|
|
|
EN
60870-2-1:1996 Telecontrol
equipment and systems - Part 2: Operating conditions - Section 1: Power
supply and electromagnetic compatibility (IEC
60870-2-1:1995) |
|
|
|
EN
60945:2002 Maritime
navigation and radiocommunication equipment and systems - General
requirements - Methods of testing and required test results (IEC 60945:2002) |
|
|
|
EN
60947-1:2004 Low-voltage
switchgear and controlgear - Part 1: General rules (IEC
60947-1:2004) |
|
|
|
EN
60947-2:2003 Low-voltage
switchgear and controlgear - Part 2: Circuit-breakers (IEC
60947-2:2003) |
|
|
|
EN
60947-2:2006 Low-voltage
switchgear and controlgear - Part 2: Circuit-breakers (IEC 60947-2:2006) |
|
|
|
EN
60947-3:1999 Low-voltage
switchgear and controlgear - Part 3: Switches, disconnectors,
switch-disconnectors and fuse-combination units (IEC
60947-3:1999) |
|
|
|
Amendment A1:2001 to EN 60947-3:1999 (IEC
60947-3:1999/A1:2001) |
Note 3 |
Date expired |
|
EN
60947-4-1:2001 Low-voltage
switchgear and controlgear - Part 4-1: Contactors and motor-starters -
Electromechanical contactors and motor-starters (IEC
60947-4-1:2000) |
|
|
|
Amendment A1:2002 to EN 60947-4-1:2001 (IEC
60947-4-1:2000/A1:2002) |
EN 60947-4-1 |
Date expired |
|
Amendment A2:2005 to EN 60947-4-1:2001 (IEC
60947-4-1:2000/A2:2005) |
Note 3 |
01.07.2008 |
|
EN 60947-4-2:2000 Low-voltage
switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC
semiconductor motor controllers and starters (IEC
60947-4-2:1999) |
|
|
|
Amendment A1:2002 to EN 60947-4-2:2000 (IEC
60947-4-2:1999/A1:2001) |
Note 3 |
Date expired |
|
Amendment A2:2006 to EN 60947-4-2:2000 (IEC
60947-4-2:1999/A2:2006) |
Note 3 |
01.12.2009 |
|
EN
60947-4-3:2000 Low-voltage
switchgear and controlgear - Part 4-3: Contactors and motor-starters - AC
semiconductor controllers and contactors for non-motor loads (IEC
60947-4-3:1999) |
|
|
|
Amendment A1:2006 to EN 60947-4-3:2000 (IEC
60947-4-3:1999/A1:2006) |
Note 3 |
01.11.2009 |
|
EN
60947-5-1:2004 Low-voltage
switchgear and controlgear - Part 5-1: Control circuit devices and switching
elements - Electromechanical control circuit devices (IEC
60947-5-1:2003) |
|
|
|
EN
60947-5-2:1998 Low-voltage
switchgear and controlgear - Part 5-2: Control circuit devices and switching
elements - Proximity switches (IEC
60947-5-2:1997 (Modified)) |
|
|
|
Amendment A2:2004 to EN 60947-5-2:1998 (IEC
60947-5-2:1997/A2:2003) |
Note 3 |
Date expired |
|
EN
60947-5-3:1999 Low-voltage
switchgear and controlgear - Part 5-3: Control circuit devices and switching
elements - Requirements for proximity devices with defined behaviour under
fault conditions (PDF) (IEC
60947-5-3:1999) |
|
|
|
Amendment A1:2005 to EN 60947-5-3:1999 (IEC
60947-5-3:1999/A1:2005) |
Note 3 |
01.03.2008 |
|
EN
60947-5-6:2000 Low-voltage
switchgear and controlgear - Part 5-6: Control circuit devices and switching
elements - DC interface for proximity sensors and switching amplifiers ( (IEC 60947-5-6:1999) |
|
|
|
EN
60947-5-7:2003 Low-voltage
switchgear and controlgear - Part 5-7: Control circuit devices and switching
elements - Requirements for proximity devices with analogue output (IEC
60947-5-7:2003) |
|
|
|
EN
60947-6-1:1991 Low-voltage
switchgear and controlgear - Part 6-1: Multiple function equipment -
Automatic transfer switching equipment (IEC
60947-6-1:1989) |
|
|
|
Amendment A2:1997 to EN 60947-6-1:1991 (IEC
60947-6-1:1989/A2:1997) |
EN 60947-6-1:1991/A11:1997 |
Date expired |
|
EN
60947-6-1:2005 Low-voltage
switchgear and controlgear - Part 6-1: Multiple function equipment - Transfer
switching equipment (IEC
60947-6-1:2005) |
|
|
|
EN
60947-6-2:2003 Low-voltage
switchgear and controlgear - Part 6-2: Multiple function equipment - Control
and protective switching devices (or equipment) (CPS) (IEC
60947-6-2:2002) |
|
|
|
EN
60947-8:2003 Low-voltage
switchgear and controlgear - Part 8: Control units for built-in thermal
protection (PTC) for rotating electrical machines (IEC
60947-8:2003) |
|
|
|
Amendment A1:2006 to EN 60947-8:2003 (IEC
60947-8:2003/A1:2006) |
Note 3 |
01.10.2009 |
|
EN
60974-10:2003 Arc
welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
(IEC
60974-10:2002 (Modified)) |
|
|
|
EN
61000-3-2:2000 Electromagnetic
compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current
emissions (equipment input current up to and including 16 A per phase) (IEC
61000-3-2:2000 (Modified)) |
|
|
|
Amendment A2:2005 to EN 61000-3-2:2000 (IEC
61000-3-2:2000/A1:2001 |
Note 3 |
01.01.2008
|
|
EN
61000-3-2:2006 Electromagnetic compatibility (EMC) - Part 3-2:
Limits - Limits for harmonic current emissions (equipment input current <=
16 A per phase) (IEC 61000-3-2:2005) |
|
|
|
EN
61000-3-3:1995 Electromagnetic
compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes,
voltage fluctuations and flicker in public low-voltage supply systems, for
equipment with rated current <= 16 A per phase and not subject to
conditional connection (IEC
61000-3-3:1994) |
|
|
|
Amendment A1:2001 to EN 61000-3-3:1995 (IEC
61000-3-3:1994/A1:2001) |
Note 3 |
Date expired |
|
Amendment A2:2005 to EN 61000-3-3:1995 (IEC
61000-3-3:1994/A2:2005) |
Note 3 |
01.09.2008 |
|
EN
61000-3-11:2000 Electromagnetic
compatibility (EMC) - Part 3-11: Limits - Limitation of voltage changes,
voltage fluctuations and flicker in public low-voltage supply systems -
Equipment with rated current <= 75 A and subject to conditional connection
(IEC
61000-3-11:2000) |
|
|
|
EN
61000-3-12:2005 Electromagnetic
compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents
produced by equipment connected to public low-voltage systems with input
current > 16 A and <= 75 A per phase (IEC
61000-3-12:2004) |
|
|
|
EN
61000-6-1:2001 Electromagnetic
compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential,
commercial and light-industrial environments (IEC
61000-6-1:1997 (Modified)) |
|
|
|
EN
61000-6-1:2007 Electromagnetic
compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential,
commercial and light-industrial environments (IEC 61000-6-1:2005) |
|
|
|
EN
61000-6-2:2001 Electromagnetic
compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial
environments (IEC
61000-6-2:1999 (Modified)) |
|
|
|
EN
61000-6-2:2005 Electromagnetic
compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial
environments (IEC 61000-6-2:2005) |
|
|
|
EN
61000-6-3:2001 Electromagnetic
compatibility (EMC) - Part 6-3: Generic standards - Emission standard for
residential, commercial and light-industrial environments (CISPR/IEC
61000-6-3:1996 (Modified)) |
|
|
|
Amendment A11:2004 to EN 61000-6-3:2001 |
Note 3 |
Date expired |
|
EN
61000-6-3:2007 Electromagnetic
compatibility (EMC) - Part 6-3: Generic standards - Emission standard for
residential, commercial and light-industrial environments (IEC
61000-6-3:2006) |
|
|
|
EN
61000-6-4:2001 Electromagnetic
compatibility (EMC) - Part 6-4: Generic standards - Emission standard for
industrial environments (IEC
61000-6-4:1997 (Modified)) |
|
|
|
EN
61000-6-4:2007 Electromagnetic
compatibility (EMC) - Part 6-4: Generic standards - Emission standard for
industrial environments (IEC 61000-6-4:2006) |
|
|
|
EN
61008-1:1994 Electrical
accessories - Residual current operated circuit-breakers without integral
overcurrent protection for household and similar uses (RCCB's) - Part 1:
General rules (IEC
61008-1:1990 (Modified) |
|
|
|
Amendment A2:1995 to EN 61008-1:1994 (IEC
61008-1:1990/A2:1995) |
Relevant generic standard(s) |
Date expired |
|
Amendment
A14:1998 to EN 61008-1:1994 |
Relevant generic standard(s) |
Date expired |
|
EN
61008-1:2004 Residual
current operated circuit-breakers without integral overcurrent protection for
household and similar uses (RCCB's) - Part 1: General rules (IEC
61008-1:1996 (Modified) |
|
|
|
EN
61009-1:1994 Electrical
accessories - Residual current operated circuit-breakers with integral
overcurrent protection for household and similar uses (RCBO's) - Part 1:
General rules (IEC
61009-1:1991 (Modified)) |
|
|
|
Amendment A1:1995 to EN 61009-1:1994 (IEC
61009-1:1991/A1:1995) |
Relevant generic standard(s) |
Date expired |
|
Amendment A14:1998 to EN 61009-1:1994 |
Note 3 |
Date expired |
|
EN
61009-1:2004 Residual
current operated circuit-breakers with integral overcurrent protection for
household and similar uses (RCBO's) - Part 1: General rules (IEC
61009-1:1996 (Modified) |
|
|
|
EN
61131-2:2003 Programmable
controllers - Part 2: Equipment requirements and tests (IEC
61131-2:2003) |
|
|
|
EN
61204-3:2000 Low
voltage power supplies, (IEC
61204-3:2000) |
|
|
|
EN
61326:1997 Electrical
equipment for measurement, control and laboratory use - EMC requirements (IEC
61326:1997) |
|
|
|
Amendment A1:1998 to EN 61326:1997 (IEC
61326:1997/A1:1998) |
Note 3 |
Date expired |
|
Amendment A2:2001 to EN 61326:1997 (IEC
61326:1997/A2:2000) |
Note 3 |
Date expired |
|
Amendment A3:2003 to EN 61326:1997 (IEC
61326:2002 (Annexes E & F only) |
Note 3 |
Date expired |
|
EN
61326-1:2006 Electrical
equipment for measurement, control and laboratory use - EMC requirements -
Part 1: General requirements (IEC
61326-1:2005) |
|
|
|
EN
61326-2-1:2006 Electrical
equipment for measurement, control and laboratory use - EMC requirements -
Part 2-1: Particular requirements - Test configurations, operational
conditions and performance criteria for sensitive test and measurement
equipment for EMC unprotected applications (IEC
61326-2-1:2005) |
|
|
|
EN
61326-2-2:2006 Electrical
equipment for measurement, control and laboratory use - EMC requirements -
Part 2-2: Particular requirements - Test configurations, operational
conditions and performance criteria for portable test, measuring and
monitoring equipment used in low-voltage distribution systems (IEC
61326-2-2:2005) |
|
|
|
EN
61326-2-3:2006 Electrical
equipment for measurement, control and laboratory use - EMC requirements -
Part 2-3: Particular requirements - Test configuration, operational conditions
and performance criteria for transducers with integrated or remote signal
conditioning (IEC
61326-2-3:2006) |
|
|
|
EN
61326-2-4:2006 Electrical
equipment for measurement, control and laboratory use - EMC requirements -
Part 2-4: Particular requirements - Test configurations, operational
conditions and performance criteria for insulation monitoring devices
according to IEC 61557-8 and for equipment for insulation fault location
according to IEC 61557-9 (IEC
61326-2-4:2006) |
|
|
|
EN
61326-2-5:2006 Electrical
equipment for measurement, control and laboratory use - EMC requirements -
Part 2-5: Particular requirements - Test configurations, operational
conditions and performance criteria for field devices with interfaces
according to IEC 61784-1, CP 3/2 (IEC
61326-2-5:2006) |
|
|
|
EN
61543:1995 Residual
current-operated protective devices (RCDs) for household and similar use -
Electromagnetic compatibility (IEC
61543:1995) |
|
|
|
Amendment A11:2003 to EN 61543:1995 |
Note 3 |
Date expired |
|
Amendment A12:2005 to EN 61543:1995 |
Note 3 |
01.03.2008 |
|
Amendment A2:2006 to EN 61543:1995 (IEC
61543:1995/A2:2005) |
Note 3 |
01.12.2008 |
|
EN
61547:1995 Equipment
for general lighting purposes - EMC immunity requirements (IEC
61547:1995) |
|
|
|
Amendment A1:2000 to EN 61547:1995 (IEC
61547:1995/A1:2000) |
Note 3 |
Date expired |
|
EN
61800-3:1996 Adjustable
speed electrical power drive systems - Part 3: EMC product standard including
specific test methods (IEC
61800-3:1996) |
|
|
|
Amendment A11:2000 to EN 61800-3:1996 |
Note 3 |
Date expired |
|
EN
61800-3:2004 Adjustable
speed electrical power drive systems - Part 3: EMC requirements and specific
test methods (IEC
61800-3:2004) |
|
|
|
EN
61812-1:1996 Specified
time relays for industrial use - Part 1: Requirements and tests (IEC
61812-1:1996) |
|
|
|
Amendment A11:1999 to EN 61812-1:1996 |
Relevant generic standard(s) |
Date expired |
|
EN
62020:1998 Electrical
accessories - Residual current monitors for household and similar uses (RCMs)
(IEC
62020:1998) |
|
|
|
Amendment A1:2005 to EN 62020:1998 (IEC
62020:1998/A1:2003 (Modified)) |
Relevant generic standard(s) |
01.03.2008 |
|
EN
62040-2:2006 Uninterruptible
power systems (UPS) - Part 2: Electromagnetic compatibility (EMC)
requirements (IEC 62040-2:2005) |
|
|
|
EN
62052-11:2003 Electricity
metering equipment (AC) - General requirements, tests and test conditions -
Part 11: Metering equipment (IEC
62052-11:2003) |
|
|
|
EN
62052-21:2004 Electricity
metering equipment (a.c.) - General requirements, tests and test conditions -
Part 21: Tariff and load control equipment (IEC
62052-21:2004) |
|
|
|
EN
62053-11:2003 Electricity
metering equipment (a.c.) - Particular requirements - Part 11:
Electromechanical meters for active energy (classes 0,5, 1 and 2) (IEC 62053-11:2003) |
|
|
|
EN
62053-21:2003 Electricity
metering equipment (a.c.) - Particular requirements - Part 21: Static meters
for active energy (classes 1 and 2) (IEC
62053-21:2003) |
|
|
|
EN
62053-22:2003 Electricity
metering equipment (a.c.) - Particular requirements - Part 22: Static meters
for active energy (classes 0,2 S and 0,5 S) (IEC 62053-22:2003) |
|
|
|
EN
62053-23:2003 Electricity
metering equipment (a.c.) - Particular requirements - Part 23: Static meters
for reactive energy (classes 2 and 3) (IEC 62053-23:2003) |
|
|
|
EN
62054-11:2004 Electricity
metering (a.c.) - Tariff and load control - Part 11: Particular requirements
for electronic ripple control receivers (IEC
62054-11:2004) |
|
|
|
EN
62054-21:2004 Electricity
metering (a.c.) - Tariff and load control - Part 21: Particular requirements
for time switches (IEC
62054-21:2004) |
|
|
|
EN 617:2001 Continuous handling equipment and systems - Safety and EMC
requirements for the equipment for the storage of bulk materials in silos,
bunkers, bins and hoppers |
— |
|
|
EN 618:2002 Continuous handling equipment and systems - Safety and EMC
requirements for equipment for mechanical handling of bulk materials except
fixed belt conveyors |
— |
|
|
EN 619:2002 Continuous handling equipment and systems - Safety and EMC
requirements for equipment for mechanical handling of unit loads |
— |
|
|
EN 620:2002 Continuous handling equipment and systems - Safety and EMC
requirements for fixed belt conveyors for bulk materials |
— |
|
|
EN 1155:1997 Building hardware - Electrically powered hold-open devices for swing
doors - Requirements and test methods |
— |
|
|
EN 12015:2004 Electromagnetic compatibility - Product family standard for lifts,
escalators and moving walks - Emission |
EN 12015:1998 |
Date Expired (30.6.2006) |
|
EN 12016:2004 Electromagnetic compatibility - Product family standard for lifts,
escalators and moving walks - Immunity |
EN 12016:1998 |
Date Expired (30.6.2006) |
|
EN 12895:2000 Industrial trucks - Electromagnetic compatibility |
— |
|
|
EN 13241-1:2003 Industrial, commercial and garage doors and gates - Product standard -
Part 1: Products without fire resistance or smoke control characteristics |
— |
|
|
EN 13309:2000 Construction machinery - Electromagnetic compatibility of machines
with internal electrical power supply |
— |
|
|
EN 14010:2003 Safety of machinery - Equipment for power driven parking of motor
vehicles - Safety and EMC requirements for design, manufacturing, erection
and commissioning stages |
— |
|
|
EN ISO 14982:1998 Agricultural and forestry machines - Electromagnetic compatibility -
Test methods and acceptance criteria (ISO 14982:1998) |
— |
|
|
EN 300 386 V1.2.1 |
EN 300 386-2 V1.1.3 |
31.8.2007 |
|
EN 300 386 V1.3.1 |
EN 300 386-2 V.1.1.3 |
31.8.2007 |
|
EN 300 386 V1.3.2 |
EN 300 386-2 V.1.1.3 |
31.8.2007 |
|
EN 300 386 V1.3.3 |
EN 300 386-2 V1.1.3 |
31.8.2007 |
|
EN 300 386-2 V1.1.3 |
|
|
General
remark: when there is a stroke in column 3 (reference of the superseded
standard), it means that the referenced standard may not be used without
amendment or particular part for EMC purpose.
Note 1: Generally the date of cessation of presumption of
conformity will be the date of withdrawal ( “dow”), set by the European
Standardisation Organisation, but attention of users of these standards is
drawn to the fact that in certain exceptional cases this can be otherwise.
Note
2.1: The new (or amended) standard has the same scope as the superseded
standard. On the date stated, the superseded standard ceases to give
presumption of conformity with the essential requirements of the directive.
Note
2.2: The new standard has a broader scope than the superseded standard. On the
date stated the superseded standard ceases to give presumption of conformity
with the essential requirements of the directive.
Note
2.3: The new standard has a narrower scope than the superseded standard. On the
date stated the (partially) superseded standard ceases to give presumption of
conformity with the essential requirements of the directive for those products
that fall within the scope of the new standard. Presumption of conformity with
the essential requirements of the directive for products that still fall within
the scope of the (partially) superseded standard, but that do not fall within
the scope of the new standard, is unaffected.
Note
3: In case of amendments, the referenced standard is EN CCCCC:YYYY, its
previous amendments, if any, and the new, quoted amendment. The superseded
standard (column 3) therefore consists of EN CCCCC:YYYY and its previous
amendments, if any, but without the new quoted amendment. On the date
stated, the superseded standard ceases to give presumption of conformity with
the essential requirements of the directive.
Example: For EN 55011:2007, the following applies :
|
EN
55011:2007 Industrial,
scientific and medical (ISM) radio-frequency equipment - Electromagnetic
disturbance characteristics - Limits and methods of measurement (CISPR 11:2003
(Modified) [The
referenced standard is EN 55011:2007] |
[The
superseded standard is EN 55011:1998 +A2: 2002 to
EN 55011:1998] |
|
|
Amendment
A2:2007 to EN 55011:2007 (CISPR
11:2003/A2:2006) [The
referenced standard is EN 55011:2007 + A2:2007 to EN 55011:2007] |
Note 3 [The
superseded standard is EN 55011:2007] |
01.11.2009 |
Note
6: EN 60947-1:1999 does not give presumption of conformity without another part
of the standard. EN 60947-1:2004 does not give presumption of conformity
without another part of the standard.
Note
7: EN 60730-1:2000 does not
give presumption of conformity without another part of the standard.
Note 8: EN 55012 is
applicable for giving presumption of conformity under directive 89/336/EEC for
those vehicles, boats and internal combustion engine-driven devices that are
not within the scope of directives 95/54/EC, 97/24/EC, 2000/2/EC or
2004/104/EC.
Note
9: EN 62052-11:2003 does not give presumption of conformity without a part of
the EN 62053 series.
Note 11: EN 62052-21:2004 does not
give presumption of conformity without a part of the EN 62054 series.
© 2005, 2010 Professional Testing & Consulting Ltd. All rights reserved.